Worksaver LRHD-6 Specifiche

0000WS65:99900663:WorkSaver™ 65Section 1 SPECIFICATIONSSection 2 CRANE DESCRIPTIONSection 3 INSTALLATIONSection 4 OPERATIONSection 5 PARTSSection 6 MA

0000WS65:99900663: 1-419921030Figure A-4. GEOMETRIC CONFIGURATION-7’ VERSION

0000WS65:99900663: 2-1199210302-1. GENERALThis section describes the assemblies thatmake up the IMT WorkSaver™ 65. Figure B-1illustrates the location

0000WS65:99900663: 2-219930503Figure B-1. CRANE COMPONENTS

0000WS65:99900663: 3-1199302113-1. GENERALThis section provides installation instructions forthe IMT WorkSaver™ Crane. See Figure E-9for specific win

0000WS65:99900663: 3-2NOTES19921030

0000WS65:99900663: 4-119921030Section 4. OPERATION4-1. GENERALThis section describes set-up, general operationand storage procedures. It is the oper

0000WS65:99900663: 4-219921030By pressing the control switch in the UPposition, lift the load slightly off the ground totest the load and effect on th

0000WS65:99900663: 4-319921030Figure D-2. BOOM POSITIONING DIAGRAM-5’ VERSIONFigure D-3. BOOM POSITIONING DIAGRAM-7’ VERSION

0000WS65:99900663: 4-419921030Figure D-4. STORED POSITION-TALL BASE MODELS

0000WS65: 5-1Section 5. PARTSFigure E-1. SERIAL NUMBER PLACARD99900663.01.200007065-1. GENERALThis section contains the parts drawings andaccompanyi

0000WS65:99900663:REVISIONS LISTDATE LOCATION DESCRIPTION OF CHANGE20010213 5-02 ecn9000-41710972-1/2-13 HEX NUT WAS JAM NUT20011018 1-2, 5-9 through

0000WS65: 5-241710972.01.REV. D 20060321Figure E-4. MAST ASM-5' & 7' VERSION (41710972)Figure E-3. BASE WELDMENTS1. 52710977 BASE WELDM

0000WS65: 5-341711029.01.19921030ITEM PART NUMBER DESCRIPTION QTY 1. 52710978 LOWER BOOM 1 2. 52710971 EXTENSION BOOM 1 3. 70144211 PIN 3/4X6-1

0000WS65: 5-441711028.01.19921030ITEM PART NUMBER DESCRIPTION QTY 1. 52710979 LOWER BOOM 1 2. 52710970 EXTENSION BOOM 1 3. 70144211 PIN 3/4X6-1

0000WS65: 5-531711022.01.19960603ITEM PART NUMBER DESCRIPTION QTY 1. 60116446 SIDE PLATE 2 2. 71732760 HOOK 1.5TON SWIVEL 1 3. 70056480 SHEAVE 5

0000WS65: 5-641711170.01.19940712ITEM PART NUMBER DESCRIPTION QTY 1. 77041461 REMOTE CONTROL HANDLE 1 2. 77041460 CONTROL BOX ASSEMBLY 1 3. 517

0000WS65: 5-795711049.01.20000517ITEM PART NO. DESCRIPTION QTY 1. 71393600 CAPACITY PLACARD 1 2. 70393645 DECAL-WORKSAVER 2 3. 70392814 DECAL-D

0000WS65: 5-8OUTRGERS.01.1997062316" OUTRIGGER ASSEMBLY (41711174)20" OUTRIGGER ASSEMBLY (41711106)24" OUTRIGGER ASSEMBLY (41711175)27&

0000WS65:99900663: 6-1200110186-1. GENERALThe WorkSaver™ 65 is easy to maintain but toprovide for maximum service life from this unit,a program of per

0000WS65:99900663: 6-2199210306-4. CRANE ELECTRICALInspect the winch motor and control box forsecure electrical contacts and the presence ofmoisture.

0000WS65:99900663: 6-320011018Figure F-1. MAINTENANCE POINTS

0000WS65:99900663:-READ FIRST-SAFETY PRECAUTIONS19971010Read and understand the IMT Operator’s CraneSafety Manual before operation of the crane.DO NOT

0000WS65:99900663: 6-419921030When using the torque data in the charts above, the following rules should be observed.1. Bolt manufacturer’s particular

0000WS65:99900663: 6-519960322

0000WS65:99900663: 6-620000706WARRANTY COVERAGE - Products manufactured by IowaMold Tooling Co., Inc. (IMT) are warranted to be free fromdefects in ma

0000WS65:99900663:20000801NOTES

0000WS65:99900663:PARAGRAPH TITLE PAGESection 1. SPECIFICATIONS1-1. GENERAL 1-11-2. LIFTING CAPACITY 1-11-3. PERFORMANCE CHARACTERISTICS 1-11-4. POWE

0000WS65:99900663: 20011018LIST OF ILLUSTRATIONSFIGURE TITLE PART NUMBER PAGEA-1. CAPACITY CHART 1-2A-3. GEOMETRIC CONFIGURATION - 5' VERSION 1-3

0000WS65:99900663: 1-1Section 1. SPECIFICATIONSWorkSaver ™ 65199212111-1. GENERAL SPECIFICATIONS5' VERSION 7' VERSIONCRANE RATING 6500 ft-

0000WS65:99900663: 1-2200306111-6. CONTROLSRemote control with a 10'-0" (3.05m) detachable control cable. The included battery cable is 25

0000WS65:99900663: 1-319921030Figure A-3. GEOMETRIC CONFIGURATION-5’ VERSION